Polymer PTC Resettable Fuse For Battery Protection LP-CW Series
Features
Protection for NiCd/NiMH rechargeable battery packs, Li-ion /Polymer Li-ion battery
Product Dimensions Part number Min Max Min Max Min Max Min Max Min Max Min Max
25.6 - 0.8 2.8 3.6 7.0 8.0 7.0 8.0 2.4 2.6
Thermal Derating Chart-IH(A) Maximum ambient operating temperatures(℃)
LP-CW110 2.0 1.7 1.4 1.2 1.1 0.8 0.6 0.5 0.3 0.2 0.1
LP-CW170 3.2 2.7 2.2 1.80 1.7 1.3 1.0 0.8 0.5 0.3 0.1
LP-CW175 3.2 2.7 2.2 1.84 1.75 1.3 1.0 0.8 0.5 0.3 0.1
LP-CW200 3.7 3.2 2.6 2.12 2.0 1.5 1.2 0.9 0.5 0.3 0.1
LP-CW210 4.1 3.5 2.9 2.26 2.1 1.6 1.3 1.0 0.7 0.4 0.1
LP-CW240 4.4 3.7 3.1 2.54 2.4 1.8 1.5 1.2 0.9 0.5 0.1
Typical Time-to-Trip Charts at 25℃ Electrical Characteristic Part number (A) (A) (V) (A) (Ω) (Ω) (Ω)
LP-CW200 2.0 4.7 16 100 0.9 10.0 5.0 0.022 0.039 0.078
LP-CW210 2.1 4.7 16 100 1.2 10.0 5.0 0.018 0.030 0.060
LP-CW240 2.4 5.9 16 100 1.2 12.0 5.0 0.014 0.026 0.052
Marking System Part Numbering System LP-CW 210 S N D U F -2 Test Procedures And Requirements Test Conditions Accept/Reject Criteria Physical Characteristics and Environmental Specifications Physical Characteristics
0.125mm nominal thickness,quarter-hard nickel
Environmental Specifications Test Conditions Resistance Electrical Specifications: IH=Hold current: maximum current at which the device will not trip at 25℃ still air. IT=Trip current: minimum current at which the device will always trip at 25℃ still air. Vmax=Maximum voltage device can withstand without damage at rated current. Imax=Maximum fault current device can withstand without damage at rated voltage. Ttrip=Maximum time to trip(s) at assigned current. Pd=Typical power dissipation: typical amount of power dissipated by the device when in state air environment. Rmin=Minimum device resistance at 25℃ prior to tripping. Rmax=Maximum device resistance at 25℃ prior to tripping. Packaging and Storage Packaging
The maximum ambient temperature shall not exceed 40℃. Storage temperatures higher than 40℃ could
result in the deformation of packaging materials. The maximum relative humidity recommended for storage is
70%. High humidity with high temperature can accelerate the oxidation of the solder plating on the termination
and reduce the solderability of the components. Sealed plastic bags with desiccant shall be used to reduce
the oxidation of the termination and shall only be opened prior to use. The products shall not be stored in
areas where harmful gases containing sulfur or chlorine are present.
Warning: PPTC devices are intended for protection against occasional over-current or over-temperature fault conditions, and should not be used when repeated fault conditions are anticipated. Operation beyond maximum ratings or improper use may result in device damage and possible electrical arcing and flame. Notes: The specification is intended to present application, product and technical data to assist the user in selecting PPTC circuit production devices. However, users should independently evaluate and test the suitability of each product. Wayon makes no warranties as to the accuracy or completeness of the information and disclaims any liability resulting from its use. Wayon’s only obligations are those in the Wayon Standard Terms and Conditions of Sale and in no case will Wayon be liable for any incidental, indirect, or consequential damages arising from the sale, resale, or misuse of its products. Wayon reserves the right to change or update, without notice, any information contained in this specification.
CHAMBRE DES DEPUTES HEURE D’ACTUALITE au sujet de LA SCOLARISATION ET DE L’ENCADREMENT DES ENFANTS ATTEINTS DE L’ADHS (Attention-Deficit / Hyperactivity Syndrom) Här President, Dir Dammen an Dir Hären, Kanner mat engem ADHS-Stéierungsbild oder esougenannte Zappelphilippen ginn oft zu Onrecht stigmatiséiert. Si ginn en nët einfache Leidenswee, grad esou hiert Ëmfeld, hi